Question: How Much Is A Ton Of Asphalt?

How do you calculate tons of asphalt?

How to Calculate Asphalt TonnageUse a tape measure to determine distances.

Convert the length, width and height measurements to feet by dividing by 12, since each foot contains 12 inches.

Multiply the length times the width times the depth to obtain the volume in cubic feet of the space to be paved.More items….

How much does a truckload of asphalt cost?

Material Costs The average price of good quality asphalt is $85 to $150 per ton.

Which is cheaper asphalt or cement?

Cost. The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot. … In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation. Finishes, details and stains can increase the price tag to as much as $15.00 per square foot.

Can I Asphalt my own driveway?

Making your own asphalt driveway is hard work, and not a job for one person. … If you have friends who will help you, it is possible to save a lot of money by doing your own driveway, even after the cost of rental equipment is factored in.

How much does it cost to pave a 300 foot driveway?

Other sources estimate the cost to install an asphalt driveway to be between $2,300 and $10,300. Homeowners typically pay per square foot. Reibling adds the average cost per square foot is between $3.50 and $4.50. Some asphalt contractors may charge by the ton, with the cost ranging from $100 to $150 per ton.

How many sq ft are in a ton?

600 sq ftAC Capacity = 600 sq ft * 0.0016 tons/sq ft = 1 Ton In general, for every 600 sq ft, you need 1 ton of AC.

How much does a ton of asphalt cover?

The area that 1 ton of asphalt covers depends on the thickness of the asphalt to be used; for a half-inch thick section of asphalt, 1 ton will cover approximately 316 square feet, while 1 ton of asphalt will cover 79 square feet when laid several inches thick.

How much does a dump truck load of asphalt cost?

The average price of good quality asphalt is $85 to $150 per ton. Simply so, how much is a dump truck load of asphalt? A concrete driveway 90 feet long and ten feet wide would be around $1800 for materials plus an additional $2000 or so for labor, for a total cost of nearly $4000.

How many tons of asphalt are in a dump truck?

Super Dumps are capable of hauling payloads from 19 to 26 tons, if you can properly distribute the loads to each axle. A typical tandem dump truck is limited to about a 13-ton payload in accordance with federal bridge law. Increased truck capacity is important when directly unloading into the asphalt paver.

How thick should asphalt be?

2-inchThe 2-inch-thick layer of blacktop should be fine as long as the gravel base is installed correctly. Adding extra blacktop thickness will not significantly extend the life of the surface. Keep in mind that blacktop is available in many different blends and mixtures.

What is the average cost of asphalt?

Cost. Ignoring any maintenance costs, asphalt is generally much cheaper to install than concrete. On average, the cost per square foot for asphalt will run between $2.50 to $4.00.

How much does it cost to pave a 50 foot driveway?

Paving an asphalt driveway costs $4,719 on average, with a typical range between $2,931 and $6,559. This project runs $7 to $13 per square foot, including $2 to $6 per square foot for materials and $5 to $7 per square foot for labor. If you need replacement, you’ll pay $8 to $15 per square foot.